Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Just got an email they cancelled the order.
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Dead I guess. Shows $59 now.
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
I've been eyeballing this for awhile and bought one a couple months ago at full price. What pushed me over was when a 2x4 kicked back and hit me hard af in the chest and arm. I was skeptical at...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Good for Smaller Jobs
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
To the people complaining about the price, these are a lot cheaper than stitches. If I bought one in the first place I would not had to have 5 stitches in my thumb. I consider myself lucky it could...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Safety equipment designed by “Stumpy Nubs”? I guess he learned how to protect fingers the hard way.
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
What table saw do you have that has a riving knife that must be removed to use this? I've had 3 different saws and not a single one required removal of the riving knife to use these product. Only the...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
I can't wait for the DIY or similar version to be sold for a lot less on Ebay. As several have commented earlier, $50 for a piece of plastic is too steep even if it's near the lowest price ever and...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
3D printing is awesome for stuff like this...
https://www.thingiverse.com/make:563943
IIRC to print these with a decent infill it will take about .5KG of filament (~$5) and a few dollars at the...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Does this only work with wood or does it grip/stick to other materials? I never know what I might want to end up pushing through the table saw....
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
If you set the blade height roughly a half tooth higher than the workpiece, then you'll have about 3 inches of pushblock between you and the blade.
You're right, the end of the cut can have your...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
uh, i'm a complete table saw newb but it seems you still don't want to put your hands over/near the blade, and pulling the piece through the back is awkward. am i missing something?
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
some people like designing. some people like googling. i'm a bit of both.
https://www.thingiverse.com/thing:2056511
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
OP's original forum (and FP) title was "Micro Jig GRR-Ripper 3D Pushblock". Unless you already know what that is, you wouldn't know it's "for Table Saws & More".
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
I'd like to get this but man $50 for a piece of plastic is a lot considering there are much cheaper (albeit not as fancy) options available.
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Thanks!
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
Never had to remove the knife to use these. If you are using a guard and pawls then you shouldn’t need a push stick.
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
This post got me to looking at prices. Ended up buying a new one on eBay for $41 shipped. Been hoping to get one at a discount for a while now.
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
I also have a Shark Guard and really like that and also have a GRR. I can recommend both as good products. Some people say use push sticks, which I use as well, but for very thin cuts the GRR I feel...
Micro Jig GRR-Ripper 3D Pushblock $47.20
Expired
Thread created 03-14-2019 by Drawingmecrazy
+63 Score
49 Replies
20,408 Views
For those interested in an aftermarket riving knife to go along with these, the Shark Guard is worth a look: it's designed so you can install or remove the blade guard in a few seconds:...
Page 1 of
3
1
2
3