This collaborative space allows users to contribute additional information, tips, and insights to enhance the original deal post. Feel free to share your knowledge and help fellow shoppers make informed decisions.
i used an interlock kit so i could power my entire panel (all 120V circuits, not at the same time obviously), just for convenience sake. an interlock prevents you from operating the generator with the main circuit on, thus preventing back feeding your panel by accident. Back feeding is when your generator sends electricity back to the outside lines b/c someone forgot to turn the main circuit breaker off. this mistake could (and has) injure or kill a line worker who is out there making repairs. direct feeding a panel without interlock or transfer switch sub panel is illegal due t potential for back feeding. here are some steps regarding interlock. as always, check your local codes for adherence to regulation.
Step 4: Buy L14-30 to L5-30 adapter cable where both hots are crossed so you can power BOTH sides of your panel even though you have a 120V generator: http://www.amazon.com/gp/product/...ge_o02_s00 . You could make your own cable for $10, but it's nice to have a factory molded rugged cable that you don't have to worry about. One end of this cable will go into the L14-30 inlet in #3 and the other end gives you a L5-30 connection. See step 5.
Step 5: Buy a 25ft or 50ft L5-30 extension cord (length is up to you). This cord is what will go from your adapter in your inlet in Step 3 to your generator. I bought this: http://www.amazon.com/Conntek-20571-Generator-Extension-Eextension/dp/B003HUYK5Q/ref=sr_1_11?ie=UTF8...[amazon.com] . The reason why I am suggesting that you buy the L5-30 cord instead of a regular 5-15 cord + L5-30 to 5-15 adapter, is to future proof your setup should you ever decide to buy a 2nd Inverter generator and use the parallel kit (which has a L5-30 plug for 3000W output power), it's up to you really and what you think you generator power needs might be in the future. if you only plan on using single 120V inverter gens like this (1 of them), save the money and use a 5-15 cord and a L5-30 to 5-15 adapter
Step 7: Either do it yourself per the Youtube videos or pay an electrician. You can buy the rest of the materials at Home Depot (romex, wall anchors, conduit, etc). Since you are providing all materials or most of them, the electrician should only be charging you a labor rate. This job should not take longer than 2 hours. If you are running across long distances or through thick masonry...ok add an hour. You should not have to pay more than 2-3 labor hrs for this job. If you want to save money, you can do all of the labor intensive work of mounting the inlet, running the conduit, and running the romex...then all he has to do is install the interlock panel, the double pole breaker for the generator, and make the final connection to your box. Figure he'll charge you (1) labor hour to do all of that. if you have never done anything electrical before, just hire the electrician for peace of mind.
NOTE 1: You will not be able to power any 240V appliances with this generator.Turn OFF all 240V circuits (except the double pole circuit you are using with your generator inlet and interlock). This is to prevent the possibility of overloading the neutral
NOTE 2: i attached photos. don't pay attention to the fact there are (2) inlets. it's b/c where i installed these, it's a multi residence with 2 service panels
NOTE 3: since i had the panels open, i threw on whole house surge protectors. bought them from a slickdeal back in 2012 i think
NOTE 4: you can fit (2) of these on a harbor freight large dolly, using scrap deck boards across.
NOTE 5: it's good practice to install run meters on these. installation simple the meter itself is only $5-6 on ebay or amazon. the run meter wire is what you see on the last pic of the 2 red generators, coming out from the front vent
$400 is a good price for a Super Quiet 2250-Watt Portable Inverter Generator
This is from their web page: Wenproducts
About Us
WEN Products was founded in 1951 by Mr. Nick Anton who led the tool world into POWER TOOLS. The advent of electricity positioned WEN Products to innovate and bring power tools to the American home.
During the next 50 years, WEN Products pioneered the electric soldering gun, electric jigsaw, chain saw, engraver, knife and wet wheel sharpener. In addition, WEN introduced random orbit technology to the consuming public. In 2001, WEN reached its 50th anniversary and celebrated by selling its 50 millionth consumer unit.
Sales of 50 million units is pretty impressive.
Today, WEN, located in Elgin, Illinois, is transforming as a homeowner and project brand that continues to offer value and quality. Along with a World-Class Customer Service center, every WEN tool customer has access to service, parts and technical information to help make their tool last for years.
Last edited by sdddg007 April 2, 2020 at 02:48 PM.
I have a truck camper with 30 amp wire. I like the idea of being able to plug directly into a 30 amp receptacle that some generators have. Will I lose some power by using an adapter of I buy this unit? My camper has a/c asking with some other stuff.
Thanks!! This is the deal I've been waiting for. I almost jumped on the ai Power 2000w generator deal posted recently, but this is the exact model I was looking for (I had it in my amazon cart @ $500). The one has a little more juice and the auto shut-off feature seems valuable for my use case of emergency use (with a lot of storage in between). My understanding is that it runs the gas out of the carbs when it's turned off.
No sales tax in OH is a bonus.
Last edited by ItsABingo April 3, 2020 at 06:01 AM.
I have two of the 2000 watt units and the Wen parallel kit which enables them to be connected for more power. Very similar to this. I also bought a similar magnetic dipstick that I used in each generator. I did pick up some metal shavings. The generators work well and are quiet. They can be a pain to start (like 10 pulls) if sitting for a while. I run them under a load every few months. The parallel kit enables me to run my 30 amp camper AC and everything else if needed. Solid purchase in my mind.
1
Like
Helpful
Funny
Not helpful
Sign up for a Slickdeals account to remove this ad.
Leave a Comment
Top Comments
i used an interlock kit so i could power my entire panel (all 120V circuits, not at the same time obviously), just for convenience sake. an interlock prevents you from operating the generator with the main circuit on, thus preventing back feeding your panel by accident. Back feeding is when your generator sends electricity back to the outside lines b/c someone forgot to turn the main circuit breaker off. this mistake could (and has) injure or kill a line worker who is out there making repairs. direct feeding a panel without interlock or transfer switch sub panel is illegal due t potential for back feeding. here are some steps regarding interlock. as always, check your local codes for adherence to regulation.
Step 1: Find an interlock kit that's compatible with your panel. Chances are the model in HD/Lowe's will not fit your. You can buy them here https://www.geninterloc
Step 2: Buy a double pole breaker that's compatible with your electrical box. Home Depot or your local electric supply house will have this.
Step 3: Buy generator inlet: http://www.amazon.com/Reliance-Controls-PB30-Generator-Generators/dp/B000BQT47S/ref=sr_1_1?ie=UTF8&q... [amazon.com]
Step 4: Buy L14-30 to L5-30 adapter cable where both hots are crossed so you can power BOTH sides of your panel even though you have a 120V generator: http://www.amazon.com/gp/product/...ge_o02_s00 . You could make your own cable for $10, but it's nice to have a factory molded rugged cable that you don't have to worry about. One end of this cable will go into the L14-30 inlet in #3 and the other end gives you a L5-30 connection. See step 5.
Step 5: Buy a 25ft or 50ft L5-30 extension cord (length is up to you). This cord is what will go from your adapter in your inlet in Step 3 to your generator. I bought this: http://www.amazon.com/Conntek-20571-Generator-Extension-Eextension/dp/B003HUYK5Q/ref=sr_1_11?ie=UTF8... [amazon.com] . The reason why I am suggesting that you buy the L5-30 cord instead of a regular 5-15 cord + L5-30 to 5-15 adapter, is to future proof your setup should you ever decide to buy a 2nd Inverter generator and use the parallel kit (which has a L5-30 plug for 3000W output power), it's up to you really and what you think you generator power needs might be in the future. if you only plan on using single 120V inverter gens like this (1 of them), save the money and use a 5-15 cord and a L5-30 to 5-15 adapter
Step 6: Buy L5-30 to 5-15 adapter plug which goes into the generator if you want to run directly from a single generator and not the parallel kit (you should have the option of doing both, as a fall back, so you aren't forcing yourself to run both): http://www.amazon.com/Conntek-Locking-Adapter-Female-Connector/dp/B002YB108Y/ref=sr_1_5?tag=slickdea... [amazon.com]
Step 7: Either do it yourself per the Youtube videos or pay an electrician. You can buy the rest of the materials at Home Depot (romex, wall anchors, conduit, etc). Since you are providing all materials or most of them, the electrician should only be charging you a labor rate. This job should not take longer than 2 hours. If you are running across long distances or through thick masonry...ok add an hour. You should not have to pay more than 2-3 labor hrs for this job. If you want to save money, you can do all of the labor intensive work of mounting the inlet, running the conduit, and running the romex...then all he has to do is install the interlock panel, the double pole breaker for the generator, and make the final connection to your box. Figure he'll charge you (1) labor hour to do all of that. if you have never done anything electrical before, just hire the electrician for peace of mind.
NOTE 1: You will not be able to power any 240V appliances with this generator.Turn OFF all 240V circuits (except the double pole circuit you are using with your generator inlet and interlock). This is to prevent the possibility of overloading the neutral
NOTE 2: i attached photos. don't pay attention to the fact there are (2) inlets. it's b/c where i installed these, it's a multi residence with 2 service panels
NOTE 3: since i had the panels open, i threw on whole house surge protectors. bought them from a slickdeal back in 2012 i think
NOTE 4: you can fit (2) of these on a harbor freight large dolly, using scrap deck boards across.
NOTE 5: it's good practice to install run meters on these. installation simple the meter itself is only $5-6 on ebay or amazon. the run meter wire is what you see on the last pic of the 2 red generators, coming out from the front vent
https://www.homedepot.c
https://www.amazon.com/gp/product/B07643J11X
117 Comments
Sign up for a Slickdeals account to remove this ad.
This is from their web page: Wenproducts
About Us
WEN Products was founded in 1951 by Mr. Nick Anton who led the tool world into POWER TOOLS. The advent of electricity positioned WEN Products to innovate and bring power tools to the American home.
During the next 50 years, WEN Products pioneered the electric soldering gun, electric jigsaw, chain saw, engraver, knife and wet wheel sharpener. In addition, WEN introduced random orbit technology to the consuming public. In 2001, WEN reached its 50th anniversary and celebrated by selling its 50 millionth consumer unit.
Sales of 50 million units is pretty impressive.
Today, WEN, located in Elgin, Illinois, is transforming as a homeowner and project brand that continues to offer value and quality. Along with a World-Class Customer Service center, every WEN tool customer has access to service, parts and technical information to help make their tool last for years.
https://www.homedepot.c
https://www.walmart.com/ip/WEN-Su.../300975917
https://www.amazon.com/gp/product/B07643J11X
Sign up for a Slickdeals account to remove this ad.
No sales tax in OH is a bonus.
Sign up for a Slickdeals account to remove this ad.
Leave a Comment