expired Posted by achhu26 • Aug 26, 2024
Aug 26, 2024 12:37 PM
Item 1 of 1
expired Posted by achhu26 • Aug 26, 2024
Aug 26, 2024 12:37 PM
Linksys LN1301 Tri-Band AX4200 WiFi 6 Wireless Router
+ Free Shipping w/ Prime$15
$50
70% offWoot!
Visit Woot!Good Deal
Bad Deal
Save
Share
Top Comments
With wireless mesh (instructions below), it's one heck of a deal and blows DECO AX5000 deal out of the water, imho.
EDIT: UPDATED instructions for enabling MESH (thanks to @rbtcordell for the original source):
1-Setup your Main router completely.
2-Plug your child node using the wan port to the main router lan port, wait for a solid purple light on the child node before proceeding
3-Log into your main router web admin.
4-Click on CA at the bottom right.
5-Click on Connectivity and CA Router setup.
6-Click on both Add Wired and Add Wireless nodes buttons. Wait for the Add wireless button to re-enable.
7-Click Done adding Child Nodes and then Apply.
8-Now the child node light should start flashing purple and turn into a mesh mode when it turns blue.
9-Disconnect Ethernet and wait for blue light again.
10-Move node to desired location.
https://forum.dd-wrt.com/phpBB2/v...?p=1304991
openwrt release notes
https://github.com/asd333111/open...ax-fd13d50
disassembly photos for the curious
https://imgur.com/a/linksys-ln130...ly-YJM1qfw
qualcommax: ipq807x: add support for Linksys MX4300 (LN1301)
Hardware specification:
========
SoC: Qualcomm IPQ8174
Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2)
RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band)
WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11)
WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
1. Disable DHCP (optional)
2. Set the device to Bridge Mode under Connectivity tab
3. Connect cable from your router to a LAN port.
4. Get some nail polished and a round sticker to cover the annoying flashing right light.
5. Click the 'AC' at the bottom of the page to see the detail configurations of wifi.
1,158 Comments
Sign up for a Slickdeals account to remove this ad.
Would this be an upgrade on that?
Further, if I bought 4 of these to use as a mesh system, would the main unit attach to the CR3100 router, or would it replace the CR3100 router that Verizon gave me?
I don't actually need these ATM. I will eventually replace my TM-AC-1900s I use for APs that cost more than double this, but I don't have any spare 5Ghz APs. The factory firmware ought to work in bridge mode.
You could add this linksys as a dumb access point but it wont be recognized as a Deco nor managed or optimized by the Mesh system. Deco system lets you buy any model deco to use with it, there are frequently older model decos available for cheap that would be much better than this linksys for you. Like that costco Deco deal underway.
Just my $0.02
Sign up for a Slickdeals account to remove this ad.
Excited to try DD-WRT on this.
Sign up for a Slickdeals account to remove this ad.
Thanks. I've seen people mentioning that they want to add to their DECO system in SD and got curious!