expired Posted by achhu26 ā¢ Aug 26, 2024
Aug 26, 2024 12:37 PM
Item 1 of 1
expired Posted by achhu26 ā¢ Aug 26, 2024
Aug 26, 2024 12:37 PM
Linksys LN1301 Tri-Band AX4200 WiFi 6 Wireless Router
+ Free Shipping w/ Prime$15
$50
70% offWoot!
Visit Woot!Good Deal
Bad Deal
Save
Share
Leave a Comment
Top Comments
With wireless mesh (instructions below), it's one heck of a deal and blows DECO AX5000 deal out of the water, imho.
EDIT: UPDATED instructions for enabling MESH (thanks to @rbtcordell for the original source):
1-Setup your Main router completely.
2-Plug your child node using the wan port to the main router lan port, wait for a solid purple light on the child node before proceeding
3-Log into your main router web admin.
4-Click on CA at the bottom right.
5-Click on Connectivity and CA Router setup.
6-Click on both Add Wired and Add Wireless nodes buttons. Wait for the Add wireless button to re-enable.
7-Click Done adding Child Nodes and then Apply.
8-Now the child node light should start flashing purple and turn into a mesh mode when it turns blue.
9-Disconnect Ethernet and wait for blue light again.
10-Move node to desired location.
https://forum.dd-wrt.com/phpBB2/v...?p=1304991
openwrt release notes
https://github.com/asd333111/open...ax-fd13d50
disassembly photos for the curious
https://imgur.com/a/linksys-ln130...ly-YJM1qfw
qualcommax: ipq807x: add support for Linksys MX4300 (LN1301)
Hardware specification:
========
SoC: Qualcomm IPQ8174
Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2)
RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band)
WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11)
WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
1. Disable DHCP (optional)
2. Set the device to Bridge Mode under Connectivity tab
3. Connect cable from your router to a LAN port.
4. Get some nail polished and a round sticker to cover the annoying flashing right light.
5. Click the 'AC' at the bottom of the page to see the detail configurations of wifi.
1,158 Comments
Sign up for a Slickdeals account to remove this ad.
https://firmware-selector.openwr
https://firmware-selector.openwr
Seriously though, I've been using the Qualcomm Max-NSS snapshot [github.com] for about three months now without any issues. Honestly, I'm a bit hesitant to upgrade to the official firmware at this point. I assume I can simply use the official Sysupgrade image to overwrite the Qualcomm Max installation, and it should work fine. However, I'm not entirely sure about this, so I'll wait until I can confirm compatibility.
Overall, installing OpenWrt has been a great experience. The main feature I rely on is DFS support [howtogeek.com], which the stock firmware lacks. My setup is as follows:
1 - OpenWrt-flashed MX4300 as the master router and switch, with Wi-Fi disabled. It's used for its firewall, DHCP leases, and assignments.
2 - OpenWrt-flashed MX4300 as a DFS Wi-Fi hub for all my streaming, wireless, bandwidth-heavy devices (Channels 64 and 128). DFS has been excellent in my highly congested Wi-Fi area, providing exclusive channels for optimal speeds and stability. I've placed the DFS hub at the center of my home, about 25 feet away from the master router/switch.
3 - Three MX4300s running stock firmware in Mesh mode for all my 2.4 GHz needs, spread across my home. These include Wi-Fi IP cameras and IoT devices, which are on their own separate Wi-Fi network. I tried OpenWrt's Mesh, but found the stock firmware delivered the best performance.
Leave a Comment