Creality 3D Overseas Store via AliExpress [aliexpress.us] has Creality Ender 3 V3 SE 3D Printer 250mm/s Print Speed & Auto Leveling on sale for $162.87 - $32 when you apply code AEUS32 during checkout = $130.87. Shipping is free.
This item ships from a USA warehouse.
Note: Price may fluctuate slightly and will vary depending on the product chosen. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. To add your address, go to Settings via the drop-down menu at the top of the page, then select Shipping Address. You may have to
manually type in the promo code to apply it at checkout.
Product Details:- Printing Technology : Fused Deposition Modeling
- Product Dimensions : 349*364*490mm
- Build Volume :220*220*250mm
- Typical Printing Speed :180mm/s
- Max. Printing Speed :250mm/s (Data from printing test with CR-PLA.)
- Acceleration : 2500mm/s2
- Layer Height :0.1-0.35mm
- Printing Accuracy :+0.1mm
- Leveling Mode :Auto Leveling
- Nozzle Temperature : <260°C
- Heatbed Temperature :<100°C
- Mainboard Type :32-bit Silent Mainboard
- Build Surface: PC Spring Steel
- Display Screen :3.2" Color Knob Screen
- Supported Filaments : PLA, PETG,TPU(95A)
Leave a Comment
6 Comments
Sign up for a Slickdeals account to remove this ad.
If you keep an eye on Creality's used/return sales, you can often pick one up for $100 bucks give or take.
They are a nice first printer actually. Quality and speed is nice. About the only thing you can't print with is ABS and the like, as it can't get to those temps with the stock configuration.
correct me if i'm wrong; i thought the thing keeping most folks from printing abs wasn't just the bed temps but the ambient temps causing the need for enclosures either heated or at least able to keep heat inside.
my (may-be-totally-wrong) "understanding" was room temp air would cause the base and the body to cool at too different rates and cause shrinkage chaos
***i know your post said you don't print in abs - but the part where you said "all my enders" makes me assume you have a lot more experience than me
Some observations:
- Enders get a bad rep and everyone always says Id ReCoMmeND a BamBu but for the price, it has been amazing in performance but not without its nuances
- Auto Z works very well, I re-level once in a while and get very nice first layers with 95-97% print success rate for the first 9 months (probably 1000 hours, I ran it daily). Now I'm about 80% success rate but can dial it up more if I sit and watch first layers to adjust the Z a bit to promote adhesion, but most days I'm lazy and just let it run.
- After that some parts needed to be replaced but if you know how to use a wrench, use YouTube, and have some technical diagnosing ability, they were very easy fixes. I replaced the extruder, the hot end and then finally the auto-z leveler itself. Total parts for replacement over 2 years has been roughly $100 and a few hours of understanding/diagnosing and then very little time swapping the parts
- swapping parts involves a tiny wrench and an Allen wrench, it's easy so even novices should not be worried
- it's been a fun experience and I think the ROI of an ender vs dropping 2-3x the price immediately for a BamBu was worth it. However I am of the type to want to understand things for how they work. Not just a set it and forget it kind of person
- it prints PLA (all variants) and PETG without issue. I tried TPU with little success
Overall happy with the price, learning and value this has brought. I also find it a powerful statement to say that I have plenty of disposable income to buy a Bambu, flash forge, etc with no hesitation but honestly don't think it's necessary. An upgrade, sure - necessary, not really. My ender works for exactly my use case.
I was you too and also have committed lots of time to it since then. Hope my above comment helps.
Leave a Comment