Makita SP6000J1 6-1/2" Plunge Circular Saw Track Saw Kit w/ Case + 55" Guide Rail

Stu_22

Nov 28, 2022 5:06 AM

63 Comments

Joined May 2006

Stu_22Nov 28, 2022 5:06 AM

63 Comments

Quote from BlitzkriegTiger

:

It should say 376.99 base price -25 for the promo ( no coupon needed, auto promo) then your sales tax rate

my total was 367.83

Doh!! I didn't take it to the end. Bought!! Ho Ho Ho - thanks!!

NewUser2022

Nov 28, 2022 5:12 AM

155 Comments

Joined Nov 2018

NewUser2022Nov 28, 2022 5:12 AM

155 Comments

Been out of woodworking for quite a while but I have to ask, what does this do compared to a Delta Unisaw table saw with a 52" Unifence? Tnx

nahpungnome

Nov 28, 2022 5:40 AM

1.7K Comments

Joined Nov 2012

nahpungnomeNov 28, 2022 5:40 AM

1.7K Comments

Quote from NewUser2022

:

Been out of woodworking for quite a while but I have to ask, what does this do compared to a Delta Unisaw table saw with a 52" Unifence? Tnx

Probably easier to cut really long sheets moving a small saw vs moving the large sheets onto the table saw.

1

ryanaugust

Nov 28, 2022 5:51 AM

469 Comments

Joined Sep 2007

ryanaugustNov 28, 2022 5:51 AM

469 Comments

Quote from NewUser2022

:

Been out of woodworking for quite a while but I have to ask, what does this do compared to a Delta Unisaw table saw with a 52" Unifence? Tnx

Preference and depends on what your cutting. If I am cutting a full sheet of osb with many different measurements, I'll use a track saw. If I have smaller pieces that are easy to handle or if I am repeatedly ripping the same size. I'll use a table saw. When I am cutting the ends off decking so that everything is perfectly straight, back to the cordless track saw... the table saw is just too hard to turn upside down and run down the length of the deck :-0

ryanaugust

Nov 28, 2022 5:57 AM

469 Comments

Joined Sep 2007

ryanaugustNov 28, 2022 5:57 AM

469 Comments

Quote from IncompletePerfect

:

I'm surprised Makita didn't do any decent 40v deals this year. I'd like the XGT track saw, but I don't need it.
What I did need is the 40v duster... my gawsh that thing is awesome. It's worth getting into the XGT 40V alone! Lol

I haven't used the 40v tracksaw yet but I'm not sure there would be much advantage as the 18v is actually 18v x 2 batteries just like their circular saw. That's what I have and while I only use it occasionally, when I need it, it is great!

2

ElatedKestrel3820

Nov 28, 2022 11:35 AM

509 Comments

Joined Nov 2018

ElatedKestrel3820Nov 28, 2022 11:35 AM

509 Comments

Quote from jaspr180

:

It's going to depend on job site vs home/shop where most already have a table saw. If I were ripping multiple items the same width, I would rather just use the table saw. If it's just a one off cut on a job, I wouldn't even think about dust collection and would prefer battery. Some guys have a track saw sitting in their truck/trailer and it's only used for those one off cuts.

I disagree here… I can rip a sheet of plywood a lot easier by myself with my track saw…. And every bit as accurate… I do however have the Festool Cordless and a 109" track… I would suggest a corded version if you're not using on the Jobsite… but I use my cordless version perpetually.

jep08

Nov 28, 2022 1:35 PM

946 Comments

Joined Nov 2011

jep08Nov 28, 2022 1:35 PM

946 Comments

Quote from IncompletePerfect

:

Well, not everyone has a high end dust extractor with automatic turn on... and the corded Makita doesn't have that feature (to which the makita isn't that good with)

In my shop I use a full size dust collector which I have above my tables. So the hose feeds and retracts.

Now, I'm limited by space, and Flaccid Paralysis in my left arm/leg. So I make things that function great for my limitations. So I figure, if I can use them, it would definitely benefit others with both arms/legs.

Manually handling a hose and power cord is fine... I just don't handle either, even if I had two arms I'd avoid it by creating something.

The hose/cord hanging off the end/edge always seem to catch. Even with the 3d printed ramps people sell on Etsy lol.

So, if a 0erson just has a shop vac, and hasn't spent a large amount on a dust extractor, then odds are, they're going to need to focus on other things staying clear and turning them on/off.

As far as batteries go, they're really inexpensive if you buy the clones. And yeah, you get a out 1 or 2 hard use years out of them. But it makes life do much easier. Especially if you don't have a $600+ extractor. And if outlets aren't available.

So, the nonsensical aspect... sure. I've had more concussions than than most NFL starting lineups... so, i can be a bit nonsensical. Ill give you that.

But I'm trying to offer advice on a larger scale. And I'm not assuming everyone has a $600+ extractor with AWS or another auto-start feature. L

Also, I definitely wouldn't consider a brushed, corded tool an upside... especially not a "Huge upside". The only downside on a cordless would be battery cost, and possible, weight. But it's been decades since I heard anyone say a corded hand tool is the better choice... especially with one that is designed for mobility, and clean space environments.

But hey... do you bro.

I agreed with you in many points but I just want to say that the cord track saw works just fine, not too complicated as you pointed out. I used this exactly cord version which I bought for $100 on Marketplace 3 years ago and cut hundreds of 4x8 sheet of plywood without any hassle. I first hooked it up to my Ridgid shop vac and use a automatic vacuum switch to automatically turn both of them on at the same time. I then upgraded to Festool dust extractor and the saw works in the same way.

I do agree that the cordless is more convenient sometimes especially when you have to bring the saw to the store or jobsite where you don't have a power source, but believe me, this cord track saw will make 90% of people happy.

Just my 2 cents.

3

FantasticRose106

Nov 28, 2022 2:14 PM

4 Comments

Joined Oct 2021

FantasticRose106Nov 28, 2022 2:14 PM

4 Comments

Quote from ryanaugust

:

Preference and depends on what your cutting. If I am cutting a full sheet of osb with many different measurements, I'll use a track saw. If I have smaller pieces that are easy to handle or if I am repeatedly ripping the same size. I'll use a table saw. When I am cutting the ends off decking so that everything is perfectly straight, back to the cordless track saw... the table saw is just too hard to turn upside down and run down the length of the deck :-0

If you're not flipping your sliding table saw upside down for the deck, you're not a real woodworker. :-P

NathanM6327

Nov 28, 2022 5:36 PM

21 Comments

Joined May 2014

NathanM6327Nov 28, 2022 5:36 PM

21 Comments

Home Depot has the Ryobi Tracksaw Kit for $299. It's 18V brushless and cordless.

Probably comparing apple to oranges, but would that the worth it over this? Just cuz of cordless, slightly cheaper overall, etcs.

1

ryanaugust

Nov 28, 2022 6:23 PM

469 Comments

Joined Sep 2007

ryanaugustNov 28, 2022 6:23 PM

469 Comments

Quote from FantasticRose106

:

If you're not flipping your sliding table saw upside down for the deck, you're not a real woodworker. :-P

It's probably more likely as a General Contractor I'd try it in a pinch.

1

baldwig

Nov 28, 2022 7:17 PM

303 Comments

Joined Aug 2014

baldwigNov 28, 2022 7:17 PM

303 Comments

I've had this saw and track for a year and paid more. I don't use it as much as I thought I would. I also didn't get the first part of the guide cut cleanly, which makes it harder to use because I can't just set the track on my marks and go. I have needed to use my track saw clamps as the underside isn't grippy enough for my applications.

Caleo

Nov 28, 2022 7:37 PM

6.7K Comments

Joined Dec 2004

CaleoNov 28, 2022 7:37 PM

6.7K Comments

Quote from baldwig

:

I've had this saw and track for a year and paid more. I don't use it as much as I thought I would. I also didn't get the first part of the guide cut cleanly, which makes it harder to use because I can't just set the track on my marks and go. I have needed to use my track saw clamps as the underside isn't grippy enough for my applications.

I use the clamps on pretty much all cuts, especially in nicer wood. Rather not make an easily avoidable mistake on expensive hardwood. You can get replacement 'guide' strips, fwiw.. you can also use a heat gun to gently remove & re-place the existing guide a little further out & re-cut it again. It helps having two tracks & a joining kit here, because you can join them THEN cut the guide where they're joined.

LetsDoSlick

Nov 28, 2022 9:55 PM

635 Comments

Joined Aug 2012

LetsDoSlickNov 28, 2022 9:55 PM

635 Comments

Damn... Saw too late, seems OOS

slickwilly15

Nov 28, 2022 10:17 PM

167 Comments

Joined Jan 2009

slickwilly15Nov 28, 2022 10:17 PM

167 Comments

1. Deal appears dead.

2. I researched the hell out of track saws and came to this. Be aware that Makita makes track/guide compatible circular saws, that are kinda the best of both worlds (for example XSH08 18v version). You get 7 1/4" depth of cut, more power, ability to lock depth, blade guard, etc, but a base that can ride on guides/track just like a 6 1/2" track saw.

3. You can also adapt just about any circular saw to use track/guides. There are several options from Kreg, and multiple adapters from Makita (ie 198673-2) that use their track. This allows you to get into the track saw world for WAY cheaper, and with much more flexibility (ie. large saws, small saws, top handle, rear handle, blade left, blade right, corded, 18v, 36v, 40v, maybe even light metal???)

In the end, I decided not to get a dedicated track saw. Might be a great option for a cabinet maker with a small shop and no panel saw with limited space where a table saw isn't feasible, or a contractor who wants ultimate portability without fussing around with clunky adapters....but even then, I think the guide compatible circular saws are better all around for these use cases.....and for most people, multiple circular saws that can be adapted to track guides if needed are best. In the end, track saws are just way, way, way too expensive for what they are. I really don't get why they have to be so insanely expensive vs their very similar circular saw brethren.

Sooooo, if you missed this "deal", I wouldn't worry about it too much. Look at the XSH08, Makita adapters, or Kreg options (ACS table, accu-cut jigs, etc.) or Festool MFT table (similar to Kreg)

Last edited by slickwilly15 November 28, 2022 at 02:19 PM.

NathanM6327

Nov 28, 2022 10:23 PM

21 Comments

Joined May 2014

NathanM6327Nov 28, 2022 10:23 PM

21 Comments

Quote from slickwilly15

:

1. Deal appears dead.

2. I researched the hell out of track saws and came to this. Be aware that Makita makes track/guide compatible circular saws, that are kinda the best of both worlds (for example XSH08 18v version). You get 7 1/4" depth of cut, more power, ability to lock depth, blade guard, etc, but a base that can ride on guides/track just like a 6 1/2" track saw.

3. You can also adapt just about any circular saw to use track/guides. There are several options from Kreg, and multiple adapters from Makita (ie 198673-2) that use their track. This allows you to get into the track saw world for WAY cheaper, and with much more flexibility (ie. large saws, small saws, top handle, rear handle, blade left, blade right, corded, 18v, 36v, 40v, maybe even light metal???)

In the end, I decided not to get a dedicated track saw. Might be a great option for a cabinet maker with a small shop and no panel saw with limited space where a table saw isn't feasible, or a contractor who wants ultimate portability without fussing around with clunky adapters....but even then, I think the guide compatible circular saws are better all around for these use cases.....and for most people, multiple circular saws that can be adapted to track guides if needed are best. In the end, track saws are just way, way, way too expensive for what they are. I really don't get why they have to be so insanely expensive vs their very similar circular saw brethren.

Sooooo, if you missed this "deal", I wouldn't worry about it too much. Look at the XSH08, Makita adapters, or Kreg options (ACS table, accu-cut jigs, etc.) or Festool MFT table (similar to Kreg)

Just to add to this. Also have came across True Trac kit $189 & $289:
https://www.amazon.com/TRACK-SAW-...97e41410bb

I'm leaning toward getting this kit because I own a nice Dewalt DCS578 60V Flexvolt circular saw that I'd miss a whole lot by going with a non-brushless corded version.

Makita SP6000J1 6-1/2" Plunge Circular Saw Track Saw Kit w/ Case + 55" Guide Rail

$352

$774

Editor's Notes

Original Post

Editor's Notes

Original Post

Community Voting

Top Comments

Join The Conversation

69 Comments

Join The Conversation

Related Searches