Direct Tools Factory Outlet has
RIDGID 13" Thickness Corded Planer (Factory Blemished) on sale for
$239.99. Shipping is Flat-Rate $14.99.
Thanks community member
dudeomega2000 for sharing this deal
About Factory Blemished Condition:
- "Like New" Merchandise with a slight cosmetic flaw that carries full manufacturer's warranty
Features:
- Chip impeller dust removal system to effectively pull wood chips from the workpiece for improved cuts and a cleaner work area
- Sure-cut carriage lock to lock the cutter head to help minimize snipe at the end of the workpiece
- Large infeed/outfeed table extensions for extra workpiece support to help eliminate snipe
- Steel top with glides for extra wide area to easily stage your material for its next cut
- Easy-to-reach, adjustable, top-mounted handle with 1/16 in. per revolution precision
- Ind-I-Cut depth gauge for instantly measuring the cutting depth before each pass
- 8-adjustable repeat-a-cut depth stops to precisely plane multiple workpieces to consistent, desired thickness for repetitive tasks
Leave a Comment
Top Comments
I can tell you, compared to the DeWalt big boi, this is much cheaper and not built nearly as well. No comparison. However, compared to other lunchbox planers, this is a big step up since it has three reversible blades. The finish is therefore cleaner, more practical cost of ownership, and seems like the alignment is pretty solid as well. I've changed blades several times and they always set in nicely. Cool little magnet tool as expected comes w this.
I can feel the grip swiftly going on the rollers after just a couple hundred board feet of already flat 12" shelving wood (just wanted to clean them up). Didn't improve after I cleaned it either
Snipe is about 2-3" but you can work that out, and you're not going to avoid it with any planer really.
For the money, I'd buy it again in a heart beat. I paid $256 for this and I added two extra sets of blades for $48 since they were on sale, totaling about 305 plus tax and shipping.
43 Comments
Sign up for a Slickdeals account to remove this ad.
You'll find that most jointers in that price range are only 6" which you can find plenty of used because people quickly upgrade from that size. Starting with 8" saves you from all that trouble. The Wen isn't as fast as as most 8" jointers, but it's about half the price of other spiral models in 8" size. I like it a lot and the value is great.
You do not need to mail them in! I have registered probably 10 different items from 6 different orders in the last two years, all online. If you'd like me to walk you through it I can. It only takes about a week for them to confirm and all you need to provide is a PDF of your invoice and the serial number from the tool.
You do not need to mail them in! I have registered probably 10 different items from 6 different orders in the last two years, all online. If you'd like me to walk you through it I can. It only takes about a week for them to confirm and all you need to provide is a PDF of your invoice and the serial number from the tool.
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank Jeepermany2k
The planer head consists of a spinning blade (cutter) that sits between 2 rubber rollers that put downward force onto your board as they pull it through the machine.
As your board enters, it's only in contact with the first roller, so the head assembly flexes and tilts slightly. Because the assembly isn't completely flat at this point, the spinning cutter digs slightly deeper than the height you set on the machine….until it reaches the 2nd roller which then levels out the head assembly. Same problem occurs upon exit, so you end up with about 2" of snipe on each end of your board.
How deep the snipe is depends on a lot of factors, and how much work you want to put into correcting it. It can be as simple as using leftover sacrificial boards to run through the machine before and after your work piece. As long as they are all butted up together when run through the planer, the snipe will only be on the sacrificial boards. This can become a juggling act though when dealing with a lot of shorter boards.
Or you just account for the snipe by starting with longer boards, and cut off the sniped ends. If you're working with cheap stuff like common construction lumber, this is usually not a problem. When you get into expensive hardwoods or exotic lumber, you'll want to avoid this.
Or you could use a sander, hand planer, or jointer to correct the snipe. There's several ways to deal with it depending on severity. There's a lot to learn when it comes to planing, so don't expect to do fine woodworking off the bat. Its not as simple as it looks unless you're doing a simple project that doesn't require high precision. It's all pretty fun though.
When people are buying things, they weigh the pros and cons and ultimately that comes down to the discount in price vs. the added risk.
Leave a Comment