ANNKE has
ANNKE Panoramic Outdoor PoE Dual Lens 6MP Security Camera (FCD600) on sale for
$89.99 when you apply promo code
DBWX6V2C12NQ at checkout.
Shipping is free.
Thanks to Staff Member
the-press-box for sharing this deal.
Features:
- 6MP & BSI Sensor, Clearer Image
- Dual-lens Fusion Splicing 180° Ultra-wide Viewing Angle
- Smart Detection Motion 2.0, Brings 99% Accurate Alerts
- Pre-Active Defense with Siren Deterrence
- Day or Night, Full Color Design Restores the Real Scene
- Synchronized Pickup, Bid Farewell to Silent Monitoring
- Built to be Prominent in the Harshest Climates
- Remote APP Control
- Multiple Storage Methods
- Two-Way Audio
- IP66 rated;designed to work for extreme indoor & outdoor use from -22 °F/-30 °C to 140 °F/60 °C.
- Built-in TF card slot
- Supports up to 256GB Micro SD card
Top Comments
"Directly from Annke, I bought 2- Annke FCD600 (I51DW) dual lens 180 cameras to use with my Annke 16-ch NVR (N46PCK). Their site listed the camera as ONVIF and supported with my NVR. I couldn't ever get both of the cameras to work with my NVR.
Contacted their customer service on their Q&A forum regarding the issue. They stated that my NVR was an early build of the N46PCK model that isn't compatible due to hardware/firmware, it was like 6m-1yr too early. They suggested I return to get a refund or run it with a separate PoE gigabit switch, which it did work.
I wish they would of specified the factory build/firmware limitation before buying them."
::Edit::
I tried to find the link to my post with tech support but it may have been removed.
/////
I received two FCD600 and tried testing both units to see their field of view. I'm not sure how long it takes for these units to connect to N46PCK NVR, after several minutes both didn't connect. I used both of the short ethernet cable provided and even connected to cables I ran to C800 and C500 around my property. I've tried putting the NVR to Factory Default, then even upgraded the firmware to V4.30.010, Build 210511.
Under Configuration>Camera>IP Channel, The FCD600 flashes while its detecting, then eventually shows connecting, now its showing Exception. It also causes Channel 5 to show exception. Viewing PoE Settings, FCD600 is only showing 3.4W of Actual Power where the other 6 cameras are between 5.7-6.3W.
Channel 5 is locked out.
/////
Dear XXXXXX,
Thanks for contacting us. This is XXXXX from ANNKE Technical Support.
I regret to tell you the earlier version of the NVR like V4.30.010, Build 210511 is NOT compatible with the FCD600 camera, because the NVR uses different hardwares. Therefore, I suggest you use the FCD600 camera alone without the NVR.
If Channel 5 is locked out, please go to 'Default' to reset the NVR to Inactive and then activate the NVR again.
Looking forward to hearing from you soon.
Best Regards,
XXXXX| Technical Support
51 Comments
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank DumbYetSmart
"Directly from Annke, I bought 2- Annke FCD600 (I51DW) dual lens 180 cameras to use with my Annke 16-ch NVR (N46PCK). Their site listed the camera as ONVIF and supported with my NVR. I couldn't ever get both of the cameras to work with my NVR.
Contacted their customer service on their Q&A forum regarding the issue. They stated that my NVR was an early build of the N46PCK model that isn't compatible due to hardware/firmware, it was like 6m-1yr too early. They suggested I return to get a refund or run it with a separate PoE gigabit switch, which it did work.
I wish they would of specified the factory build/firmware limitation before buying them."
::Edit::
I tried to find the link to my post with tech support but it may have been removed.
/////
I received two FCD600 and tried testing both units to see their field of view. I'm not sure how long it takes for these units to connect to N46PCK NVR, after several minutes both didn't connect. I used both of the short ethernet cable provided and even connected to cables I ran to C800 and C500 around my property. I've tried putting the NVR to Factory Default, then even upgraded the firmware to V4.30.010, Build 210511.
Under Configuration>Camera>IP Channel, The FCD600 flashes while its detecting, then eventually shows connecting, now its showing Exception. It also causes Channel 5 to show exception. Viewing PoE Settings, FCD600 is only showing 3.4W of Actual Power where the other 6 cameras are between 5.7-6.3W.
Channel 5 is locked out.
/////
Dear XXXXXX,
Thanks for contacting us. This is XXXXX from ANNKE Technical Support.
I regret to tell you the earlier version of the NVR like V4.30.010, Build 210511 is NOT compatible with the FCD600 camera, because the NVR uses different hardwares. Therefore, I suggest you use the FCD600 camera alone without the NVR.
If Channel 5 is locked out, please go to 'Default' to reset the NVR to Inactive and then activate the NVR again.
Looking forward to hearing from you soon.
Best Regards,
XXXXX| Technical Support
Sign up for a Slickdeals account to remove this ad.
Sign up for a Slickdeals account to remove this ad.