Item 1 of 2
Item 1 of 2
expiredmg3 posted Feb 12, 2024 2:17 PM
DeWALT 10" Jobsite Table Saw with 32.5" Rip + Rolling Stand
$439
$549
20% off
+ Free Shippingat eBay
Missed This Deal? Get alerts when similar deals are posted.
+ Free Shippingat eBayDeal Details
Factory Authorized Outlet via eBay has DeWALT 10" Jobsite Table Saw with 32.5" Rip + Rolling Stand (DWE7491RS) on sale for $439.20 when you apply coupon code PRESIDENT20 at checkout. Shipping is free.
Thanks to Community Member mg3 for finding this deal.
Condition:
Thanks to Community Member mg3 for finding this deal.
Condition:
- New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag
- 1x DeWALT 10" Jobsite Table Saw
- 1x 10" 24-Tooth Carbide Blade
- 1x Folding Table Saw Stand
- 1x Push Stick
- 1x Miter Gauge
- 1x Rip Fence
- 2x Blade Wrenches
- 1x Blade Guard Assembly
- Owner's Manual
- Patented Material Support, Can Be Used For Narrow Rip Cuts
- 32-1/2" Rip Capacity Easily Cuts A Variety Of Larger Shelving And Trim Materials
- Rolling Stand Designed For Easy Set Up And Breakdown With Excellent Stability
- Telescoping Fence Rails Retract To Create A Small, Portable Package
- Flip Over Ripping Fence Allows For Narrow Rip Cuts
- 15 Amp Motor Quickly Rips Through Hardwoods With Ease
- 2-1/2" Dust Collection Port Easily Connects To A Vacuum For Efficient Dust Extraction
- 3-1/8" Depth Of Cut At 90 And 2-1/4" At 45
- 21-7/8" X 26 - 3/8" Table Provides Superior Material Support
Editor's Notes
Written by powerfuldoppler | Staff- About this deal:
- Please see original post for additional details & give the WIKI and additional forum comments a read for helpful discussion.
Community Notes
About the Poster
Deal Details
Community Notes
About the Poster
Factory Authorized Outlet via eBay has DeWALT 10" Jobsite Table Saw with 32.5" Rip + Rolling Stand (DWE7491RS) on sale for $439.20 when you apply coupon code PRESIDENT20 at checkout. Shipping is free.
Thanks to Community Member mg3 for finding this deal.
Condition:
Thanks to Community Member mg3 for finding this deal.
Condition:
- New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag
- 1x DeWALT 10" Jobsite Table Saw
- 1x 10" 24-Tooth Carbide Blade
- 1x Folding Table Saw Stand
- 1x Push Stick
- 1x Miter Gauge
- 1x Rip Fence
- 2x Blade Wrenches
- 1x Blade Guard Assembly
- Owner's Manual
- Patented Material Support, Can Be Used For Narrow Rip Cuts
- 32-1/2" Rip Capacity Easily Cuts A Variety Of Larger Shelving And Trim Materials
- Rolling Stand Designed For Easy Set Up And Breakdown With Excellent Stability
- Telescoping Fence Rails Retract To Create A Small, Portable Package
- Flip Over Ripping Fence Allows For Narrow Rip Cuts
- 15 Amp Motor Quickly Rips Through Hardwoods With Ease
- 2-1/2" Dust Collection Port Easily Connects To A Vacuum For Efficient Dust Extraction
- 3-1/8" Depth Of Cut At 90 And 2-1/4" At 45
- 21-7/8" X 26 - 3/8" Table Provides Superior Material Support
Editor's Notes
Written by powerfuldoppler | Staff- About this deal:
- Please see original post for additional details & give the WIKI and additional forum comments a read for helpful discussion.
Community Voting
Deal
Score
+38
Good Deal
Bad Deal
Top Comments
Everyone loves lots about this saw, so I'll tell you what I don't love that much.
The miter slots are further away from the blade than many other big name saws. Enough so that most off the shelf jigs won't fly with the Dewalt. Just about every jig we use with these is shop made.
The miter gauge that's included with the saw is little more than a toy. If you're doing any kind of millwork, cabinetry or woodworking, you'll have to invest in a miter gauge. So there's another $50 to $200 into the purchase price.
The fence has to be recalibrated every time the saw is moved. It's seldom the saw actually remains true. Speaking of the fence, the aluminum extrusion Dewalt uses for the fence is very thin and in four of the five saws I have, the fence isn't even straight. I solved this with a big fat 1 inch MDF sacrificial surface on the fences, but I really expected more from a $600-$700 saw. Cripes, the $250 Skil has a nicer fence than the Dewalt. Sure, that rack and pinion is nifty, but when you slap on a crappy beer can thin aluminum extrusion, the rack means the grand sum of diddly.
The blade has to be recalibrated about once a month. I attribute this to the relatively lightweight trundle configuration and the fact that my saws are moved, loaded, unloaded, set up, taken down at least two or three times a week. Still, it's a mobile jobsite saw. Dewalt should have designed it to withstand this kind of activity and still cut a straight line.
A couple of my saws have started experiencing issues with the blade sinking during use. So if I set up a 3/4 inch blade height and start cutting material, by the time I'm done the blade height might be closer to 5/8 inch. If all your cuts are through and through, that's not really as much of an issue. But if you're cutting dados or splines or tenons or... you get the gist.
Whatever coating they use for the table top wears relatively quickly. Especially in the miter slots, creating binding on miter gauges and jigs. This is a pain in the backside and has wasted material. But in an extreme scenario could present a very dangerous situation.
After just short of two years, the legs all have a bit of slop in them. Difficult to get a good result on a precision cut when your table is wobbling.
My $0.02
Join The Conversation
Share your experience with the Slickdeals community
Share information with the community. Please follow our Community Guidelines and be kind!
44 Comments
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank ruouttaurmind
Everyone loves lots about this saw, so I'll tell you what I don't love that much.
The miter slots are further away from the blade than many other big name saws. Enough so that most off the shelf jigs won't fly with the Dewalt. Just about every jig we use with these is shop made.
The miter gauge that's included with the saw is little more than a toy. If you're doing any kind of millwork, cabinetry or woodworking, you'll have to invest in a miter gauge. So there's another $50 to $200 into the purchase price.
The fence has to be recalibrated every time the saw is moved. It's seldom the saw actually remains true. Speaking of the fence, the aluminum extrusion Dewalt uses for the fence is very thin and in four of the five saws I have, the fence isn't even straight. I solved this with a big fat 1 inch MDF sacrificial surface on the fences, but I really expected more from a $600-$700 saw. Cripes, the $250 Skil has a nicer fence than the Dewalt. Sure, that rack and pinion is nifty, but when you slap on a crappy beer can thin aluminum extrusion, the rack means the grand sum of diddly.
The blade has to be recalibrated about once a month. I attribute this to the relatively lightweight trundle configuration and the fact that my saws are moved, loaded, unloaded, set up, taken down at least two or three times a week. Still, it's a mobile jobsite saw. Dewalt should have designed it to withstand this kind of activity and still cut a straight line.
A couple of my saws have started experiencing issues with the blade sinking during use. So if I set up a 3/4 inch blade height and start cutting material, by the time I'm done the blade height might be closer to 5/8 inch. If all your cuts are through and through, that's not really as much of an issue. But if you're cutting dados or splines or tenons or... you get the gist.
Whatever coating they use for the table top wears relatively quickly. Especially in the miter slots, creating binding on miter gauges and jigs. This is a pain in the backside and has wasted material. But in an extreme scenario could present a very dangerous situation.
After just short of two years, the legs all have a bit of slop in them. Difficult to get a good result on a precision cut when your table is wobbling.
My $0.02
Glad I got one at that price but this price is even better!!
Sign up for a Slickdeals account to remove this ad.
FYI, there are some awesome plans online for a bench that incorporates this and dewalts chop saw. I plan on building one when it's a little nicer outside.
edit: my apologies, I have the 8 1/4 so this is a great deal. you have the option for dado blades and obviously a larger cut.
I still love mine but this definitely hits a few more marks.
Sign up for a Slickdeals account to remove this ad.
thanks OP!
Join The Conversation
Share your experience with the Slickdeals community
Share information with the community. Please follow our Community Guidelines and be kind!