Click here [dd-wrt.com] for a guide on installing DD-WRT
Download the latest DD-WRT builds from here [dd-wrt.com]
If you are not interested in using custom firmware yet, these routers support mesh with the stock firmware, but the USB port is disabled.
The stock firmware is relatively new, but is speculated to not receive many, if any, updates, so it may be best to wait until custom firmware support is merged and more mature before messing with installing custom firmware.
How to enable mesh:
- Setup your Main router completely.
- Plug your child node using the wan port to the main router lan port, wait for a solid purple light on the child node before proceeding.
- Log into your main router web admin.
- Click on CA at the bottom right.
- Click on Connectivity and CA Router setup.
- Click on both Add Wired and Add Wireless nodes buttons. Wait for the Add wireless button to re-enable.
- Click Done adding Child Nodes and then Apply.
- Now the child node light should start flashing purple and turn into a mesh mode when it turns blue.
- Disconnect Ethernet and wait for blue light again.
- Move node to desired location.
How to set up as access point:
- Disable DHCP (optional).
- Set the device to Bridge Mode under Connectivity tab.
- Connect cable from your router to a LAN port.
- Get some nail polish and a round sticker to cover the annoying flashing right light.
- Click the 'CA' at the bottom of the page to see the detailed configurations of wifi.
to unbrick and flash new firmware
run flashimg
run flashimg2
rename stock firmware to tortuga.img
Top Comments
Mind you that I only have 100Mbps Spectrum internet but I do stream/direct play 4k videos from a Plex media server to several Amazon Firestick 4k devices without issue. Overall IMO you would be hard pressed to find such relatively decent hardware for so cheap; especially a Mesh network.
It wasn't all smooth at first mind you. I kept getting disconnects; especially with the streaming IP cameras. But I discovered by disabling Express Forwarding all my streaming issues went away. (CA>Connectivity>Administration>Express Forwarding)
I'm guessing that Cisco's/Linksys' proprietary Express Forwarding routing protocol was causing havoc with the IP cams streaming capabilities. Also, disabling Node Steering seemed to make things more stable as well; mesh nodes no longer disconnect from the router when Node Steering is disabled. (CA>Wi-Fi Settings>Advanced>Node Steering)
Of course, user experience can vary so feel free to experiment. if the routers are giving you problems, try turning these features off and see if it works
It's not a deal if you never receive it.
Join The Conversation
Share your experience with the Slickdeals community
Share information with the community. Please follow our Community Guidelines and be kind!
1.2K Comments
Sign up for a Slickdeals account to remove this ad.
The DD-WRT wiki for this router should be the same as the mx4200.
https://wiki.dd-wrt.com/wiki/inde...sys_MX4200 [dd-wrt.com]
You need to download both the factory2ddwrt and webupgrade files. Flash the factory2ddwrt first, and once you reboot into dd-wrt, flash the webupdate two times. You will have a total of 3 flashes.
https://dd-wrt.com/support/other-...24-r58124/ [dd-wrt.com]
This ensures the latest version is installed on both partitions.
One of the posts said it should be the yellow port that does NOT say Internet?
I currently have my child units working with the Ethernet cable plugged into the Internet port.. Wondering if this is incorrect.
Sign up for a Slickdeals account to remove this ad.
One of the posts said it should be the yellow port that does NOT say Internet?
I currently have my child units working with the Ethernet cable plugged into the Internet port.. Wondering if this is incorrect.
01-Setup your Main router completely.
02-Plug your child node using the wan port to the main router lan port.
03-Log into your main router web admin. 4-Click on CA at the bottom right.
05-Click on Connectivity and CA Router setup.
06-Click on both Add Wired and Add Wireless nodes buttons. Wait for the Add wireless button to re-enable.
07-Click Done adding Child Nodes and then Apply.
08-Now the child node light should start flashing purple and turn into a mesh mode when it turns blue.
09-Disconnect Ethernet and wait for blue light again.
10-Move node to desired location.
we more beta versions now, you can pick the latest from here
https://dd-wrt.com/support/other-...%2F2024%2F
each beta version has its own improvements, if you get one version and it works for you make note of it.
You can always roll back to it, if the newer version breaks something.
01-Setup your Main router completely.
02-Plug your child node using the wan port to the main router lan port.
03-Log into your main router web admin. 4-Click on CA at the bottom right.
05-Click on Connectivity and CA Router setup.
06-Click on both Add Wired and Add Wireless nodes buttons. Wait for the Add wireless button to re-enable.
07-Click Done adding Child Nodes and then Apply.
08-Now the child node light should start flashing purple and turn into a mesh mode when it turns blue.
09-Disconnect Ethernet and wait for blue light again.
10-Move node to desired location.
I thought it should be the internet port but one post said it is the yellow port that does not say internet
Can anyone confirm which one to use once the child is configured. I.e. I'm placing it upstairs connected to ether net
Sign up for a Slickdeals account to remove this ad.
Join The Conversation
Share your experience with the Slickdeals community
Share information with the community. Please follow our Community Guidelines and be kind!