Item 1 of 3
Item 1 of 3
expiredshivster1796 posted Jul 2, 2026 3:07 AM
10-Pk 1KG KINGROON 1.75mm PETG 3D Printer Filament (Mix Color)
$60
$89
32% off
+ Free S&Hat AliExpress
Heads up, this deal has expired. Want to create a deal alert for this item?
+ Free S&Hat AliExpressDeal Details
KINGROON 3D Store via AliExpress has 10-Pack 1KG KINGROON 1.75mm PETG 3D Printer Filament (Mix Color) on sale for $65.13 - $5 with promo code USDEAL5 during checkout = $60.13. Shipping is free.
Thanks to Community Member shivster1796 for sharing this deal.
Thanks to Community Member shivster1796 for sharing this deal.
- Note: Price may fluctuate slightly with currency exchange rates. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. You may have to manually type in the promo code to apply it at checkout. This item ships from a USA warehouse. For expedited customer service, please email [email protected].
- Wire diameter: 1.75mm
- Tolerance: ±0.03mm
- Printing temperature: 230-250°C
- Bed temperature: Apply glue when unheated; no glue needed when heated (75-85°C)
- Printing speed: 50-100mm/s
- Air bubbles: 100% zero air bubbles
- Length: 1.75mm (1kg) = 320m
Editor's Notes
Written by RevOne | Staff- Rated 4.9 out of 5 stars from customer reviews.
- Price of $6.02 per KG.
- Our research indicates that this deal is $25.57 less (29% savings) than the next best available price from a reputable merchant with prices starting from $85.70 at the time of this post.
- Please see the original post for additional details & refer to the comments below for discussion.
Community Notes
About the Poster
Deal Details
Community Notes
About the Poster
KINGROON 3D Store via AliExpress has 10-Pack 1KG KINGROON 1.75mm PETG 3D Printer Filament (Mix Color) on sale for $65.13 - $5 with promo code USDEAL5 during checkout = $60.13. Shipping is free.
Thanks to Community Member shivster1796 for sharing this deal.
Thanks to Community Member shivster1796 for sharing this deal.
- Note: Price may fluctuate slightly with currency exchange rates. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. You may have to manually type in the promo code to apply it at checkout. This item ships from a USA warehouse. For expedited customer service, please email [email protected].
- Wire diameter: 1.75mm
- Tolerance: ±0.03mm
- Printing temperature: 230-250°C
- Bed temperature: Apply glue when unheated; no glue needed when heated (75-85°C)
- Printing speed: 50-100mm/s
- Air bubbles: 100% zero air bubbles
- Length: 1.75mm (1kg) = 320m
Editor's Notes
Written by RevOne | Staff- Rated 4.9 out of 5 stars from customer reviews.
- Price of $6.02 per KG.
- Our research indicates that this deal is $25.57 less (29% savings) than the next best available price from a reputable merchant with prices starting from $85.70 at the time of this post.
- Please see the original post for additional details & refer to the comments below for discussion.
Community Voting
Deal Score
+83
Good Deal
Bad Deal
Found by idk_then
Forum Thread
55% off
Found by ppxyz1
Forum Thread
Found by idk_then
Forum Thread
45% off
Found by iconian
Forum Thread
50% off
Found by TattyBear
Forum Thread
Found by Ruyi
Forum Thread
20% off
Found by LolaBunny21
Forum Thread
60% off
Found by itsamazeling
Forum Thread
70% off
Found by Vic121
Forum Thread
66% off
Top Comments
this is a pretty good price per KG for PETG but I've picked this mix color pack in May for about $50 shipped. You could be spending way more for basic PETG so I think this is a safe price point to dip your toes into.
use a release agent on your print sheet to make it much easier to remove your petg prints... I've used an elmer's glue stick in a pinch but I found that a dedicated 3d print liquid "glue" works so much better. Some people have also used hair spray. That said, I found that my Kobra X needs a release agent more than my K2.
Verify all the rolls of filament before you start printing. A box of black filament had clear instead (even the label on the spool said black) and Ali Express wanted me to return all the filament... considering that I already went through a few rolls at this point, I decided to just eat the cost since it was so cheap (Kingroon CS told me to contact AE).
Get yourself a filament dryer. I've dried all my filament before using it, just as a good rule of thumb. Desiccant helps keep your filament dry but the dryer actually removes the moisture from your filament.
Join The Conversation
Share your experience with the Slickdeals community
Share information with the community. Please follow our Community Guidelines and be kind!
49 Comments
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank mohit87
Our community has rated this post as helpful. If you agree, why not thank FancyMice600
I am expecting to use the dryer more though since I'm a humid environment and petg absorbs moisture faster than PLA supposedly
Our community has rated this post as helpful. If you agree, why not thank Kippy
Our community has rated this post as helpful. If you agree, why not thank Ajax77
Our community has rated this post as helpful. If you agree, why not thank the_badluck
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank flangomango
I have printed things for my Tesla from this filament and it does not melt inside my car unlike PLA.
If this drops to $45 again then I will buy a third box but $60 is on the high side for me.
Our community has rated this post as helpful. If you agree, why not thank Golgothan
Sign up for a Slickdeals account to remove this ad.
Join The Conversation
Share your experience with the Slickdeals community
Share information with the community. Please follow our Community Guidelines and be kind!