Update: This very popular deal is still available.
Woot! has
Linksys LN1301 Tri-Band AX4200 WiFi 6 Wireless Router on sale for
$14.99 when you apply coupon code
GEARUP4FALL at checkout.
Shipping is free for Amazon Prime Members (must login with your Amazon account and select a shipping address in order for Woot to apply free shipping) or is otherwise $6 per order.
Thanks to community member
achhu26 for sharing this deal.
About this Item:
- Covers up to 2700 sq. ft.
- Handles 40+ devices
- Speed up to 4.2 Gbps (AX4200)
- WiFi 6 Tri-Band
- Quad-Core Processor
- MU-MIMO and OFDMA
Leave a Comment
Top Comments
With wireless mesh (instructions below), it's one heck of a deal and blows DECO AX5000 deal out of the water, imho.
EDIT: UPDATED instructions for enabling MESH (thanks to @rbtcordell for the original source):
1-Setup your Main router completely.
2-Plug your child node using the wan port to the main router lan port, wait for a solid purple light on the child node before proceeding
3-Log into your main router web admin.
4-Click on CA at the bottom right.
5-Click on Connectivity and CA Router setup.
6-Click on both Add Wired and Add Wireless nodes buttons. Wait for the Add wireless button to re-enable.
7-Click Done adding Child Nodes and then Apply.
8-Now the child node light should start flashing purple and turn into a mesh mode when it turns blue.
9-Disconnect Ethernet and wait for blue light again.
10-Move node to desired location.
https://forum.dd-wrt.com/phpBB2/v...?p=1304991
openwrt release notes
https://github.com/asd333111/open...ax-fd13d50
disassembly photos for the curious
https://imgur.com/a/linksys-ln130...ly-YJM1qfw
qualcommax: ipq807x: add support for Linksys MX4300 (LN1301)
Hardware specification:
========
SoC: Qualcomm IPQ8174
Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2)
RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band)
WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11)
WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
1. Disable DHCP (optional)
2. Set the device to Bridge Mode under Connectivity tab
3. Connect cable from your router to a LAN port.
4. Get some nail polished and a round sticker to cover the annoying flashing right light.
5. Click the 'AC' at the bottom of the page to see the detail configurations of wifi.
1,158 Comments
Sign up for a Slickdeals account to remove this ad.
This model is actually MX4300 and not AX4200/MX4200 which is the original Velop.
For this model the WPS button on the bottom is unlabeled.
Not sure if it works at all.
https://store.linksys.c
Anyway the Ethernet/Internet ports are both limited to 1 gigabit per port so no difference there. If your internet speed is greater than 1 gb, you might want to pay more for the newer cable modems and wireless router that support 2.5gb or higher but those are really expensive. Eg Eero max7.
With WiFi 7 coming on board and you just want to hold over and do a little work following the instructions on page 1 of this thread, get two of this for a simple mesh.
Sign up for a Slickdeals account to remove this ad.
Excellent deal if you can wait for stable builds from your preferred firmware vendor(OpenWRT, DD-Wrt, Gargoyle, etc), or are comfortable tinkering with snapshots or custom builds.
is it reccomended to purchase a different modem to use with these? Or will my current one work just fine? Thank you guys I'm advance for the help
This model is actually MX4300 and not AX4200/MX4200 which is the original Velop.
For this model the WPS button on the bottom is unlabeled.
Not sure if it works at all.
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank ArtisanalChicken32
Leave a Comment