110-Piece DeWALT Shank Screwdriver Bit Set
Expired
$23
$49.98
+ Free Curbside Pickup
+52Deal Score
56,057 Views
Lowe's has 110-Piece DeWALT Shank Screwdriver Bit Set (DWA110SETCCLW) on sale for $22.98. Select free curbside pickup where stock permits. Thanks Rokket
Note, availability for curbside pickup may vary by location.
Editor's Notes & Price Research
Written by
This set includes the most commonly used screwdriver accessories and features the tough case container bit retention system.
It's worth noting these are screwdriver bits, not impact rated.
I'm not referring to the bit size, I'm referring to the bit material. Bits that are not impact rated are made out of softer steel and while you may not notice them deform, the absorb a LOT of the energy your impact is putting out, making it much less effective and more likely to damage the impact. I. Price this especially on longer hex bits in my 887. They absorb so much energy they get hit to the touch. Not good.
All my drills and bits and tools, they all come from garage sales.
Did my first masonry job a couple months ago.
went through 4 standard drill bits in cylinder block, before I realized I need to borrow a masonry bit from the neighbor.
Then last week at a garage sale, I found a dozen masonry bits for free! Apparently they were closing up shop and all the flipper vultures had gotten what they wanted and left.
Theres Always something good at the bottom of the bin, if you keep looking. and new things to be gained, and experience to be learned, when working on a new project.
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank Greg-J
06-16-2020 at 10:52 PM.
Quote
from sorbitol
:
Well it contains small bits as well.
I'm not referring to the bit size, I'm referring to the bit material. Bits that are not impact rated are made out of softer steel and while you may not notice them deform, the absorb a LOT of the energy your impact is putting out, making it much less effective and more likely to damage the impact. I. Price this especially on longer hex bits in my 887. They absorb so much energy they get hit to the touch. Not good.
I was just saying that the small bits aren't typically impact rated, because they miss probably just snap in half.
Interesting about energy absorption.
I wonder if you could actively cool with a water stream... Would that allow you to use any normal sized bit for impact usage?
You'll find that you can get even standard small bits that are impact rated, to use with an impact rated bit holder.
As for water cooling, you wouldn't want to. All that energy turning to heat means more wear on your tool, shorter battery life, and overall poor performance.
You'll find that you can get even standard small bits that are impact rated, to use with an impact rated bit holder.
As for water cooling, you wouldn't want to. All that energy turning to heat means more wear on your tool, shorter battery life, and overall poor performance.
Huh, Never knew or considered a bit holder.
I bent the first small bit in an impact drill, using a chuck adapter, months ago. I figured that it was impossible to use small bits.
Guess I learned something.
Based on your comments, I'd recommend avoiding DIY projects.
All my drills and bits and tools, they all come from garage sales.
Did my first masonry job a couple months ago.
went through 4 standard drill bits in cylinder block, before I realized I need to borrow a masonry bit from the neighbor.
Then last week at a garage sale, I found a dozen masonry bits for free! Apparently they were closing up shop and all the flipper vultures had gotten what they wanted and left.
Theres Always something good at the bottom of the bin, if you keep looking. and new things to be gained, and experience to be learned, when working on a new project.
All my drills and bits and tools, they all come from garage sales.
Did my first masonry job a couple months ago.
went through 4 standard drill bits in cylinder block, before I realized I need to borrow a masonry bit from the neighbor.
Then last week at a garage sale, I found a dozen masonry bits for free! Apparently they were closing up shop and all the flipper vultures had gotten what they wanted and left.
Theres Always something good at the bottom of the bin, if you keep looking. And is always experience and new things to be gained when working.
Just wait until you discover the hammer drill... 🤯
Can you make mason bit lasts more than a few holes? I got the red helix set which make fast holes thru the stucco but only a few before it wouldn't work anymore.
edit: I don't have a hammer drill but the holes are made with bushless Ryobi drill.
Can you make mason bit lasts more than a few holes? I got the red helix set which make fast holes thru the stucco but only a few before it wouldn't work anymore.
edit: I don't have a hammer drill but the holes are made with bushless Ryobi drill.
Why not sharpen them when they don't get sharp. I usually sharpen my bits once they get dull.
39 Comments
Your comment cannot be blank.
Featured Comments
Did my first masonry job a couple months ago.
went through 4 standard drill bits in cylinder block, before I realized I need to borrow a masonry bit from the neighbor.
Then last week at a garage sale, I found a dozen masonry bits for free! Apparently they were closing up shop and all the flipper vultures had gotten what they wanted and left.
Theres Always something good at the bottom of the bin, if you keep looking. and new things to be gained, and experience to be learned, when working on a new project.
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank Greg-J
Our community has rated this post as helpful. If you agree, why not thank Greg-J
I'm not referring to the bit size, I'm referring to the bit material. Bits that are not impact rated are made out of softer steel and while you may not notice them deform, the absorb a LOT of the energy your impact is putting out, making it much less effective and more likely to damage the impact. I. Price this especially on longer hex bits in my 887. They absorb so much energy they get hit to the touch. Not good.
Interesting about energy absorption.
I wonder if you could actively cool with a water stream... Would that allow you to use any normal sized bit for impact usage?
You'll find that you can get even standard small bits that are impact rated, to use with an impact rated bit holder.
As for water cooling, you wouldn't want to. All that energy turning to heat means more wear on your tool, shorter battery life, and overall poor performance.
As for water cooling, you wouldn't want to. All that energy turning to heat means more wear on your tool, shorter battery life, and overall poor performance.
I bent the first small bit in an impact drill, using a chuck adapter, months ago. I figured that it was impossible to use small bits.
Guess I learned something.
Sign up for a Slickdeals account to remove this ad.
Did my first masonry job a couple months ago.
went through 4 standard drill bits in cylinder block, before I realized I need to borrow a masonry bit from the neighbor.
Then last week at a garage sale, I found a dozen masonry bits for free! Apparently they were closing up shop and all the flipper vultures had gotten what they wanted and left.
Theres Always something good at the bottom of the bin, if you keep looking. and new things to be gained, and experience to be learned, when working on a new project.
Did my first masonry job a couple months ago.
went through 4 standard drill bits in cylinder block, before I realized I need to borrow a masonry bit from the neighbor.
Then last week at a garage sale, I found a dozen masonry bits for free! Apparently they were closing up shop and all the flipper vultures had gotten what they wanted and left.
Theres Always something good at the bottom of the bin, if you keep looking. And is always experience and new things to be gained when working.
Just wait until you discover the hammer drill... 🤯
edit: I don't have a hammer drill but the holes are made with bushless Ryobi drill.
edit: I don't have a hammer drill but the holes are made with bushless Ryobi drill.
Why not sharpen them when they don't get sharp. I usually sharpen my bits once they get dull.