GigaParts catalogue page Icom IC-7300MK2 [gigaparts.com].Icom Press release Icom Unveils New IC-7300MK2 HF / 50 / (70) MHz Transceiver [icomamerica.com] PRE-RELEASE INFORMATION HF / 50 / (70) MHz TRANSCEIVER |7300MK2 [icomamerica.com] Official company ICOM IC-7300MK2 product webpage https://www.icomjapan.c Icom IC-7300MK2 BASIC MANUAL (English) Download https://www.icomamericaThe ICOM IC-7300MK2 has many of the same features as the ICOM IC-7300.
Official company ICOM IC-7300 product webpage https://www.icomjapan.cMembers can Subscribe to this Thread to get notification when something new is posted to this thread. This can act as a daily reminder to enter.
They seem to be asking a lot of technical questions which licensed hams should know.
Your browsers AI search engine should be able to find the answer in case you don't know.
They are reusing some questions from the last time the prize was an ICOM IC-7300 in 2024.
See: https://slickdeals.net/f/17467908-gigaparts-yaesu-icom-ic-7300-august-8-2024-fcc-licensed-us-amateur-operators-only?t=17467908
I encourage you to post both the question and the answer and not just the answer..
Historically, GigaParts has repeated the same questions from one sweepstakes in later ones.
If you post the question, then in a later sweepstakes when they repeat the question you can do a
keyword search of the previous thread and quickly find the answer.
Leave a Comment
200 Comments
Sign up for a Slickdeals account to remove this ad.
In the 'Grounding' section, what must the Icom IC-7300MK2 [GND] terminal NEVER be connected to?
Answer: Gas or electric pipe
Entry page https://www.gigaparts.n
Page nineteen of the BASIC MANUAL
to a gas or electric pipe,
In 'Connecting an external DC power supply', what is the minimum capacity required for a non-Icom DC power cable used with the Icom IC-7300MK2?
Answer: 21 Amps
Entry page https://www.gigaparts.n
Page twenty of the BASIC MANUAL
transceiver needs:
• 13.8 V DC (Capacity: At least 21 Amps)
In 'Connecting the antenna tuner', what is the frequency matching range of the AH-730 when used with the Icom IC-7300MK2?
Answer: 1.8 to 54 MHz
Entry page https://www.gigaparts.n
Page twenty of the BASIC MANUAL
matching from 1.8 to 54 MHz when using at least
a 7 m (23 ft) antenna.
In 'Connecting the antenna tuner', what is the minimum antenna length required for the AH-730 tuner for the Icom IC-7300MK2?
Answer: 7 m (23 ft)
Entry page https://www.gigaparts.n
Page twenty of the BASIC MANUAL
matching from 1.8 to 54 MHz when using at least
a 7 m (23 ft) antenna.
In 'Setting the Speech Compressor', what is the ideal range for the Icom IC-7300MK2 COMP meter?
Answer: 10 to 20 dB
Entry page https://www.gigaparts.n
Page thirty one of the BASIC MANUAL
normal voice level, rotate to adjust the
Speech Compressor level to where the COMP
meter reads within the COMP zone (10 to 20 dB
range)
In In 'Notch Filter', which mode does NOT support the Icom IC-7300MK2 Auto Notch function?
Answer: CW
Entry page https://www.gigaparts.n
Page thirty five of the BASIC MANUAL
tuning signals, and so on. It can be used in the SSB,
AM, and FM modes.
In 'Setting the CW pitch control', what is the Icom IC-7300MK2 frequency step size for adjustment?
Answer: 5 Hz
Entry page https://www.gigaparts.n
Page thirty eight (38) of the BASIC MANUAL
300 and 900 Hz (in 5 Hz steps).
Sign up for a Slickdeals account to remove this ad.
In 'ANTENNA TUNER OPERATION', what SWR level does the Icom IC-7300MK2 tuner aim to reduce to after 2-3 seconds?
Answer: I don't know
I picked 'Less than 1.5:1' and they marked it incorrect.
On page forty six (46) of the BASIC MANUAL
2 ~ 3 seconds of tuning.
Entry page https://www.gigaparts.n
Question: In 'ANTENNA TUNER OPERATION', what is the maximum Icom IC-7300MK2 tuning time before the red indicator goes out?
Answer: 15 seconds.
In 'SET MODE', what is the default attenuation value added by the Icom IC-7300MK2 MF Band ATT function?
Answer: 16 dB
Entry page https://www.gigaparts.n
Page fifty two (52) of the BASIC MANUAL
other attenuation value that you have set.
In 'SET MODE', what is the default CI-V Address for the Icom IC-7300MK2?
Answer: B6h
Entry page https://www.gigaparts.n
Page fifty eight (58) of the BASIC MANUAL
In 'SET MODE', which CI-V address is reserved and cannot be used by the Icom IC-7300MK2?
Answer: 01h
Entry page https://www.gigaparts.n
Page fifty eight (58) of the BASIC MANUAL
The usable addresses are limited to 02h ~ DFh.
In 'SPECIFICATIONS', how many memory channels are available in the Icom IC-7300MK2, including scan edges?
Answer: 101
Entry page https://www.gigaparts.n
Page seventy (70) of the BASIC MANUAL
Sign up for a Slickdeals account to remove this ad.
In 'SPECIFICATIONS', what is the Icom IC-7300MK2 general receiver frequency coverage range?
Answer: 0.030–74.800 MHz
Entry page https://www.gigaparts.n
Page seventy (70) of the BASIC MANUAL
Receiver 0.030000 ~ 74.800000*
Leave a Comment