Item 1 of 2
Item 1 of 2
frontpagegabe23111 posted Mar 8, 2026 3:21 PM
Creality SpacePi X4L Filament Dryer
$99
$267
62% off
+ Free S/Hat AliExpress
+ Free S/Hat AliExpressDeal Details
Creality Overseas Store via AliExpress has Creality SpacePi X4L Filament Dryer w/ Dual Independent Chambers on sale for $114.96 - $16 when you apply promo code RDC16C at checkout = $98.96. Shipping is free.
Thanks to Community Member gabe23111 for sharing this deal.
Note: Price may fluctuate slightly with currency exchange rates. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. You may have to manually type in the promo code to apply it at checkout. This item ships from a USA warehouse. For expedited customer service, please email [email protected].
Product Details:
Thanks to Community Member gabe23111 for sharing this deal.
Note: Price may fluctuate slightly with currency exchange rates. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. You may have to manually type in the promo code to apply it at checkout. This item ships from a USA warehouse. For expedited customer service, please email [email protected].
Product Details:
- The First Choice for Muti-Color Drying
- 4 Spools
- Up to 75℃
- Dual Independent Heating Chambers
- LCD Touchscreen
- Double Safety Protection
- Moisture-proof Sealing Design
Editor's Notes
Written by Nate650 | Staff- About this deal:
- Our research indicates that this deal is $40.04 less (28.8% savings) than the next best available price from a reputable merchant with prices starting from $139 at the time of this posting.
- About this product:
- Rated 4.9 out of 5 stars based on 20 AliExpress customer reviews.
- Manufacturer product page
- Additional notes:
- Please see the original post for additional details & give the wiki and additional forum comments a read for helpful discussion.
Community Notes
About the Poster
Deal Details
Community Notes
About the Poster
Creality Overseas Store via AliExpress has Creality SpacePi X4L Filament Dryer w/ Dual Independent Chambers on sale for $114.96 - $16 when you apply promo code RDC16C at checkout = $98.96. Shipping is free.
Thanks to Community Member gabe23111 for sharing this deal.
Note: Price may fluctuate slightly with currency exchange rates. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. You may have to manually type in the promo code to apply it at checkout. This item ships from a USA warehouse. For expedited customer service, please email [email protected].
Product Details:
Thanks to Community Member gabe23111 for sharing this deal.
Note: Price may fluctuate slightly with currency exchange rates. You must be signed into your AliExpress account and have your address added to add items to your cart and place an order. You may have to manually type in the promo code to apply it at checkout. This item ships from a USA warehouse. For expedited customer service, please email [email protected].
Product Details:
- The First Choice for Muti-Color Drying
- 4 Spools
- Up to 75℃
- Dual Independent Heating Chambers
- LCD Touchscreen
- Double Safety Protection
- Moisture-proof Sealing Design
Editor's Notes
Written by Nate650 | Staff- About this deal:
- Our research indicates that this deal is $40.04 less (28.8% savings) than the next best available price from a reputable merchant with prices starting from $139 at the time of this posting.
- About this product:
- Rated 4.9 out of 5 stars based on 20 AliExpress customer reviews.
- Manufacturer product page
- Additional notes:
- Please see the original post for additional details & give the wiki and additional forum comments a read for helpful discussion.
Community Voting
Deal Score
+21
Good Deal
Bad Deal
Found by Skillful_Pickle
Forum Thread
36% off
Found by MatchuPicchu
Forum Thread
25% off
Found by idk_then
Forum Thread
56% off
Found by phoinix
Forum Thread
60% off
Found by phoinix
Forum Thread
84% off
Found by phoinix
Forum Thread
75% off
Top Comments
Join The Conversation
Share information with the community. Please follow our Community Guidelines and be kind!
10 Comments
Sign up for a Slickdeals account to remove this ad.
Our community has rated this post as helpful. If you agree, why not thank LivelyWallaby1957
Sign up for a Slickdeals account to remove this ad.
If E4 appears right when you hit Start (not later in the cycle), the dryer is basically flagging a temperature/heat start fault: it either does not see a valid thermistor reading, thinks the lid is open, or cannot begin heating correctly.
Fast checks to try
- Turn it off, unplug for 10–30 seconds, plug back in, then try again; several users report E4 disappearing after a full power reset.
- Make sure the lid is fully seated before you press Start; E4 can be thrown if it thinks the lid is open when heating begins.
- Start with one spool only, at a low temp (around 45–50 °C) using a manual program instead of a high‑temp preset like ABS/ASA; heavy or dual spools plus high temp can make it fail its initial heat‑up check.
If it still throws E4 immediately- Check that the home screen shows a sane room temperature before you start; if it already shows E4/EA or a nonsense temp, Creality's own debug steps point to a thermistor or board issue.
- If the displayed temp does not rise at all when you start heating, support recommends checking for loose thermistor wiring or replacing the mainboard; Creality has been sending replacement boards for persistent E4 on Space Pi units.
Does your Space Pi 2 show a normal ambient temperature on the screen before you press Start, or does it go straight to E4 as soon as you start the drying program?If E4 appears right when you hit Start (not later in the cycle), the dryer is basically flagging a temperature/heat start fault: it either does not see a valid thermistor reading, thinks the lid is open, or cannot begin heating correctly.
Fast checks to try
- Turn it off, unplug for 10–30 seconds, plug back in, then try again; several users report E4 disappearing after a full power reset.
- Make sure the lid is fully seated before you press Start; E4 can be thrown if it thinks the lid is open when heating begins.
- Start with one spool only, at a low temp (around 45–50 °C) using a manual program instead of a high‑temp preset like ABS/ASA; heavy or dual spools plus high temp can make it fail its initial heat‑up check.
If it still throws E4 immediately- Check that the home screen shows a sane room temperature before you start; if it already shows E4/EA or a nonsense temp, Creality's own debug steps point to a thermistor or board issue.
- If the displayed temp does not rise at all when you start heating, support recommends checking for loose thermistor wiring or replacing the mainboard; Creality has been sending replacement boards for persistent E4 on Space Pi units.
Does your Space Pi 2 show a normal ambient temperature on the screen before you press Start, or does it go straight to E4 as soon as you start the drying program?Join The Conversation
Share information with the community. Please follow our Community Guidelines and be kind!